Fender Flare Trim X-1663 BT - Sold by the CONTINUOUS YARD!

TRIM-LOK
SKU:
X1663 BT
$5.95
Bulk Pricing:

Below are the available bulk discount rates for each individual item when you purchase a certain amount

  • Buy 25 or above and pay only $4.45 each
Width:
2.00 (in)
Height:
2.00 (in)
Depth:
2.00 (in)
Current Stock:
22
Adding to cart… The item has been added
Sold by the CONTINUOUSYARD / You can order as many yards as you need!
Fender Flare Trim is an ozone resistant EPDM Rubber that mounts between the flare and the body.
3M automotive grade tape creates a solid bond between both surfaces.
Tape: BT - 3M High Strength Tape System
The ultimate bond between the rubber and substrate. Creates a moisture barrier and air tight seal between rubber
and substrate. Highest peel and shear resistance, can be used under high loads of stress and force.
Has low initial tack for easy re-positioning during installation and requires 72 hours of cure time for full bond strength. Good heat performance -20F to +158.
      Recommended temperature range for general applications: -20°F. through +150°F, Sponge Rubber (EPDM)
Application: For optimum performance - 25% - 50% maximum compression recommended.
Resistance Ratings: Excellent resistance to water absorption, ozone, sunlight aging, low temperature, and compression set.
Flammability and Code Compliance: FMVSS 302, UL 50
CLEANING AND APPLICATION INSTRUCTIONS
Regardless of bonding surface, it must be clean and free of surface contaminant such as oil, grease, mold release and dirt.
Most bonding failures are due to improperly cleaned surfaces. Prior to applying any adhesive, Clean surface with 50/50 denatured alcohol and water solution.

Reviews

  • 5
    Molding For Crown Vic. - P71

    Posted by Unknown on 23rd Jun 2020

    Needed to replace the molding between the rear tail lights and the rear quarter panel on my sons P71 Crown Vic. To my surprises, you had it, and its so much better then the original molding material, and yours has the peel and stick material on it. Thanks again. Very happy!

  • 5
    FENDER FLARE TRIM X-1663 BT

    Posted by Steve Soules on 19th Jun 2019

    This product is amazing. Easy to apply and looks awesome.

  • 5
    Flare trim

    Posted by Yoshi on 7th May 2019

    Fits well and easy to work with. Price is set right and arrived very quickly.

  • 4
    Material was easier to work with

    Posted by Glenn on 30th Nov 2016

    I tried the original material sent with the fender flares and had a lot of problems with it rolling. Purchased this material from J&J and had a better experience with getting it to stay in place.

  • 5
    works great

    Posted by Jason Covington on 29th Jul 2016

    replaced old factory gasket on my FJ80 Land cruiser flairs. Works great.

  • 5
    Fender Flare Trim X-1663 BT

    Posted by Janet Roberts on 23rd May 2016

    Personally I like this trim better than the original. It is a little wider which in appearance makes the truck look better. My husband liked the fact that it had a good deal of adhesive surface. The previous repairs were not up to par and his work and this product brought it back to good looking truck. And the option of buying just the amount required was great too. Thank You.

  • 5
    Great trim for fender flairs.

    Posted by M. Fischer on 29th Mar 2016

    Great product, just what needed to dress up the uneven fit for plastic fender flairs.

  • 5
    great trim

    Posted by Ed on 20th Feb 2016

    works great filled in gap on fender flare on my s10 crew cab thank you.

  • 5
    Great quality product

    Posted by Bob on 15th Sep 2015

    Fender flare trim matched factory trim perfectly.